Agricultural Product Processing Research Institute

Abstract Conductive hydrogels are promising interface materials utilized in bioelectronics for human–machine interactions. However, the low‐temperature induced freezing problem and water evaporation‐induced structural failures have significantly hindered their practical applications. To address these problems, herein, an elaborately designed nanocomposite organohydrogel is fabricated by introducing highly conductive MXene nanosheets into a tannic acid‐decorated cellulose nanofibrils/polyacrylamide hybrid gel network infiltrated with glycerol (Gly)/water binary solvent. Owing to the introduction of Gly, the as‐prepared organohydrogel demonstrates an outstanding flexibility and electrical conductivity under a wide temperature spectrum (from −36 to 60 °C), and exhibits long‐term stability in an open environment (>7 days). Additionally, the dynamic catechol‐borate ester bonds, along with the readily formed hydrogen bonds between the water and Gly molecules, further endow the organohydrogel with excellent stretchability (≈1500% strain), high tissue adhesiveness, and self‐healing properties. The favorable environmental stability and broad working strain range (≈500% strain); together with high sensitivity (gauge factor of 8.21) make this organohydrogel a promising candidate for both large and subtle motion monitoring.

Effective hemostasis is vital to reduce the pain and mortality of patients, and the research and development of hemostatic materials are prerequisite for effective hemostasis. Chitosan (CS), with good biodegradability, biocompatibility and non-toxicity, has been widely applied in bio-medicine, the chemical industry, the food industry and cosmetics. The excellent hemostatic properties of CS have been extensively studied. As a result, chitosan-based composite hemostatic materials have been emerging. In this review, the hemostatic mechanism of chitosan is briefly discussed, and then the progress of research on chitosan-based composite hemostatic materials with multiple forms such as films, sponges, hydrogels, particles and fibers are introduced. Finally, future perspectives of chitosan-based composite hemostatic materials are given. The objective of this review is to provide a reference for further research and development of effective hemostatic materials.

The evolution of polymer based nanoparticles as a drug delivery carrier via pharmaceutical nano/microencapsulation has greatly promoted the development of nano- and micro-medicine in the past few decades. Poly(lactide-co-glycolide) (PLGA) and chitosan, which are biodegradable and biocompatible polymers, have been approved by both the Food & Drug Administration (FDA) and European Medicine Agency (EMA), making them ideal biomaterials that can be advanced from laboratory development to clinical oral and parental administrations. PLGA and chitosan encapsulated nanoparticles (NPs) have successfully been developed as new oral drug delivery systems with demonstrated high efficacy. This review aims to provide a comprehensive overview of the fabrication of PLGA and chitosan particulate systems using nano/microencapsulation methods, the current progress and the future outlooks of the nanoparticulate drug delivery systems. Especially, we focus on the formulations and nano/micro-encapsulation techniques using top-down techniques. It also addresses how the different phases including the organic and aqueous ones in the emulsion system interact with each other and subsequently influence the properties of the drug delivery system. Besides, surface modification strategies which can effectively engineer intrinsic physicochemical properties are summarised. Finally, future perspectives and potential directions of PLGA and chitosan nano/microencapsulated drug systems are outlined.

The mechanism of a green reduction of graphene oxide by potassium carbonate as recycling deoxidizer has been revealed.

-glucoside (95.6%). The addition of 1 wt% of BBE into the film matrix resulted in a dense and compact internal microstructure, which greatly improved the water vapor permeability and tensile strength of the film. However, the addition of 2, 3 and 4 wt% of BBE into film matrix produced heterogeneous inner microstructures due to the formation of agglomerated BBE. The intermolecular interactions between BBE and the starch film matrix were through hydrogen binding. As compared with the starch film, starch-BBE films exhibited higher thicknesses, tensile strength, UV-vis light barrier and antioxidant properties. Moreover, starch-BBE films presented significant color changes when exposed to hydrogen chloride and ammonia gases. The pH-sensitive starch-BBE films were able to monitor the freshness of pork. Our results suggested that starch-BBE films could be used as smart and active packaging materials in the food industry.

The use of gelatin and gelatin-blend polymers as environmentally safe polymers to synthesis electrospun nanofibers, has caused a revolution in the biomedical field. The development of efficient nanofibers has played a significant role in drug delivery, and for use in advanced scaffolds in regenerative medicine. Gelatin is an exceptional biopolymer, which is highly versatile, despite variations in the processing technology. The electrospinning process is an efficient technique for the manufacture of gelatin electrospun nanofibers (GNFs), as it is simple, efficient, and cost-effective. GNFs have higher porosity with large surface area and biocompatibility, despite that there are some drawbacks. These drawbacks include rapid degradation, poor mechanical strength, and complete dissolution, which limits the use of gelatin electrospun nanofibers in this form for biomedicine. Thus, these fibers need to be cross-linked, in order to control its solubility. This modification caused an improvement in the biological properties of GNFs, which made them suitable candidates for various biomedical applications, such as wound healing, drug delivery, bone regeneration, tubular scaffolding, skin, nerve, kidney, and cardiac tissue engineering. In this review an outline of electrospinning is shown with critical summary of literature evaluated with respect to the various applications of nanofibers-derived gelatin.

The aim of this study was to prepare sodium alginates (SAs) with different molecular weight and G/M ratio, and characterize their rheological behaviors and emulsifying properties. The result of Fourier transform infrared (FTIR) showed that the chemical bonds among the β-d-mannuronic acid- (M-), α-l-guluronic acid- (G-), and MG-sequential blocks in the SA chains were not changed significantly by acid treatment. Meanwhile, the molecular weight and G/M ratio of the SA exhibited drastic variation after acid modification. The result of rheological analysis suggesting that the apparent viscosity of SA reduced from 30 to 16.4 mPa.s with the increase of shear rate, reveals that SA solution belongs to pseudoplastic liquid. Also, the apparent viscosity of acid-modified SA solution dropped rapidly with the decrease of the molecular weight. The properties of emulsions stabilized by SA, SA-Ms, and commercial SAs were evaluated via the interface tensiometry and determination of the zeta potential, droplet size, creaming index (CI), and Turbiscan stability index (TSI). Compared with the SA-stabilized emulsion, the interfacial tension of the emulsion stabilized by SA-M increased with the decrease of the molecular weight reduced at the similar M/G ratio. The decrease in zeta potential and the increase in TSI of the emulsion were observed with the decrease of molecular weight, indicating that molecular weight plays an important role on the emulsifying ability of SA. In addition, the SA with low G/M ratio can form emulsions with stable and fine droplets.

Ethanol production from biomass, especially waste biomass, and the use of such ethanol as fuel can reduce fossil fuel consumption and ameliorate the hidden costs of burning fossil fuels such as its environmental impact.

The fruit physico-chemical properties, antioxidant activity and mineral contents of 26 pineapple [Ananas comosus (L.) Merr.] genotypes grown in China were measured. The results showed great quantitative differences in the composition of these pineapple genotypes. Sucrose was the dominant sugar in all 26 genotypes, while citric acid was the principal organic acid. Potassium, calcium and magnesium were the major mineral constituents. The ascorbic acid (AsA) content ranged from 5.08 to 33.57 mg/100 g fresh weight (FW), while the total phenolic (TP) content varied from 31.48 to 77.55 mg gallic acid equivalents (GAE)/100 g FW. The two parameters in the predominant cultivars Comte de Paris and Smooth Cayenne were relative low. However, MD-2 indicated the highest AsA and TP contents (33.57 mg/100 g and 77.55 mg GAE/100 g FM, respectively), and it also showed the strongest antioxidant capacity 22.85 and 17.30 μmol TE/g FW using DPPH and TEAC methods, respectively. The antioxidant capacity of pineapple was correlated with the contents of phenolics, flavonoids and AsA. The present study provided important information for the further application of those pineapple genotypes.

Mussel adhesive proteins (MAPs) have a unique ability to firmly adhere to different surfaces in aqueous environments via the special amino acid, 3,4-dihydroxyphenylalanine (DOPA). The catechol groups in DOPA are a key group for adhesive proteins, which is highly informative for the biomedical domain. By simulating MAPs, medical products can be developed for tissue adhesion, drug delivery, and wound healing. Hydrogel is a common formulation that is highly adaptable to numerous medical applications. Based on a discussion of the adhesion mechanism of MAPs, this paper reviews the formation and adhesion mechanism of catechol-functionalized hydrogels, types of hydrogels and main factors affecting adhesion, and medical applications of hydrogels, and future the development of catechol-functionalized hydrogels.

3-Carene is an antimicrobial monoterpene that occurs naturally in a variety of plants and has an ambiguous antibacterial mechanism against food-borne germs. The antibacterial effects and action mechanism of 3-carene against Gram-positive Brochothrix thermosphacta ACCC 03870 and Gram-negative Pseudomonas fluorescens ATCC 13525 were studied. Scanning electron microscopy (SEM) examination and leakage of alkaline phosphatase (AKP) verified that 3-carene caused more obvious damage to the morphology and wall structure of B. thermosphacta than P. fluorescens. The release of potassium ions and proteins, the reduction in membrane potential (MP), and fluorescein diacetate (FDA) staining further confirmed that the loss of the barrier function of the cell membrane and the leakage of cytoplasmic contents were due to the 3-carene treatment. Furthermore, the disorder of succinate dehydrogenase (SDH), malate dehydrogenase (MDH), pyruvate kinase (PK), and ATP content indicated that 3-carene could lead to metabolic dysfunction and inhibit energy synthesis. In addition, the results from the fluorescence analysis revealed that 3-carene could probably bind to bacterial DNA and affect the conformation and structure of genomic DNA. These results revealed that 3-carene had strong antibacterial activity against B. thermosphacta and P. fluorescens via membrane damage, bacterial metabolic perturbations, and genomic DNA structure disruption, interfering in cellular functions and even causing cell death.

Abstract Using ultrafine calcium carbonate to reinforce natural rubber latex film, the effect of its content on latex properties such as surface tension, viscosity, mechanical stability, and heat stability and the physical properties of latex film before and after aging such as tear strength, modulus, and tensile strength were investigated. The results showed that the surface tension of natural rubber latex reinforced by ultrafine calcium carbonate only changed slightly; when the content of calcium carbonate was less than 20%, the change of viscosity was not obvious, but when the content was greater than 20%, the viscosity significantly lowered. Ultrafine calcium carbonate could effectively improve the tear strength, tensile strength, and modulus of the natural rubber latex film. The modulus increased with the increment of the calcium carbonate. When the content of calcium carbonate was less than 15%, the tear strength and tensile strength increased with the increments of calcium carbonate, but when the content was greater than 15%, the above‐mentioned properties decreased with the increment of calcium carbonate. By comprehensive consideration, the best reinforcing effect was obtained at a content of 15% ultrafine calcium carbonate. The particle diameters of calcium carbonate and their distribution in the calcium carbonate emulsion and in the rubber film were analyzed with SEM and a laser particle size tester, which showed that the distribution of calcium carbonate in the latex film was even and that it could effectively reinforce natural rubber latex film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 982–985, 2003

Abstract Inorganic nano fillers have demonstrated great potential to enhance the properties of natural rubber (NR). The present article reports the successful development of a NR nanocomposite reinforced with nano silica (SiO 2 ). Its dynamic mechanical properties, thermal aging resistance, and morphology are investigated. The results show that the SiO 2 nanoparticles are homogenously distributed throughout the NR matrix in a form of spherical nano‐cluster with an average size of 80 nm when the SiO 2 content is 4 wt%. With the introduction of SiO 2 , the thermal resistance and the storage modulus of NR host significantly increase, and the activation energy of relaxation of the nanocomposite, compared to the raw NR, increases from 90.1 to 125.8 kJ/mol. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers

Graphene is a new type of carbon material with a flexible, two-dimensional structure. Due to the excellent stability of its lattice structure and its mechanical flexibility, graphene-based materials can be applied in flexible humidity sensors. At present, the application of graphene-based flexible humidity sensors in the fields of medical care and environmental monitoring is attracting widespread attention. In this review, the basic properties of graphene oxide (GO) and reduced graphene oxide (rGO) as moisture-sensitive materials and methods for their preparation were introduced. Moreover, three methods for improving the performance of moisture-sensitive materials were discussed. The working principle of different types of graphene-based humidity sensors were introduced. The progress in the research on graphene-based flexible humidity sensors in four respects: Human respiration, skin moisture, human sweat, and environmental humidity were discussed. Finally, the future research, following the development trends and challenges, to develop the potential of integrated, graphene-based flexible humidity sensors were discussed.

The potential of superhydrophobic and superoleophilic microwrinkled reduced graphene oxide (MWrGO) structures is here demonstrated for oil spill cleanup. The impact of the thickness of MWrGO films on the sorption performance of three different oils was investigated. Water contact angles across the MWrGO surfaces were found to exceed 150°, while oil could be easily absorbed by the microwrinkled structures of MWrGO within seconds after contact. Although the oil surface diffusion rate was not found to be dependent on the thickness of the graphene oxide films, the oil sorption capacity was the largest with the thinner MWrGO films due to the high surface area resulting from their fine surface texture. Furthermore, the composite films can be repeatedly used for at least 20 oil sorption-removal cycles without any notable loss in selectivity and uptake capacity. These MWrGO/elastomer composite films could be applied as a potential candidate material for future oil spill cleanup.

The incorporation of a high percentage of targeting molecules into drug delivery system is one of the important methods for improving efficacy of targeting therapeutic drugs to cancer cells. PLGA-based drug delivery carriers with folic acid (FA) as targeting molecule have a low targeting efficiency due to a low FA conjugation ratio. In this work, we fabricated a FA-conjugated PLGA system using a crosslinker 1, 3-diaminopropane and have achieved a high conjugation ratio of 46.7% (mol/mol). The as-prepared PLGA-based biomaterial was used to encapsulate therapeutic drug 5-fluorouracil (5-FU) into nanoparticles. In the in vitro experiments, an IC₅₀ of 5.69 µg/mL has been achieved for 5-FU loaded PLGA-1, 3-diaminopropane-folic acid nanoparticles on HT-29 cancer cells and is significantly lower than that of 5-FU and 5-FU loaded PLGA nanoparticles which only have an IC₅₀ of 22.9 and 14.17 µg/mL, respectively. The fluorescent microscopy images showed that nanoparticles with FA are largely taken up by HT-29 cancer cells and the targeting nanoparticles have more affinity to cancer cells than the pure drugs and untreated nanoparticles. Therefore, the 1, 3-diaminopropane can facilitate the conjugation of FA to PLGA to form a novel polymer and 5-FU loaded PLGA-1, 3-diaminopropane-folic acid nanoparticles can be a highly efficient system for specific delivery of drugs to cancer cells.

This study explored a novel strategy to develop solid-state whole-grain oats as a novel carrier of lactic acid bacteria and a nutraceutical supplement rich in ACE inhibitory peptides. Oats were fermented by Lactobacillus plantarum B1-6, Rhizopus oryzae, or a combination of L. plantarum B1-6 and R. oryzae. L. plantarum showed a much better growth performance in oats when it was combined with R. oryzae than when it was cultured alone, as evidenced by an increase in viable cell count to 9.70 log cfu g-1 after 72 h of fermentation. The coinoculated fermented oats (CFO) and the R. oryzae-fermented oats (RFO) were then selected for investigations on protein hydrolysis and on the functional properties of the released bioactive peptides. The results showed that the soluble protein contents changed from 7.05 mg g-1 to 14.43 and 10.21 mg g-1 for CFO and RFO, respectively. However, the degree of hydrolysis and the content of peptides with molecular masses less than 10 000 Da indicated that the CFO proteins can be degraded to a greater degree. As analyzed by electrophoresis and reversed-phase high-performance liquid chromatography, the protein and peptide profiles of CFO and RFO demonstrated that the proteins from CFO were more obviously hydrolyzed and more small peptides were obtained. In addition, both CFO and RFO presented higher ACE inhibitory activities than unfermented oats, whereas the protein extracts from CFO exerted a lower IC50 value of 0.42 mg protein per mL compared with the protein extracts from the other samples. This research has broadened our knowledge on the development of whole-grain oat products as a probiotic carrier and on the difference between mixed solid-state fermentation (SSF) and fungi SSF in terms of protein degradation and the capacity to release ACE inhibitory peptides. Our approach could be used to obtain probiotic food products and probably to develop oats as a potential therapeutic ingredient targeting hypertension.

The aim of this study was to investigate modification of insoluble dietary fiber (IDF) from garlic straw with ultrasonic processing technology. The functional, physicochemical, and structural properties were evaluated. Based on the uniform design (UD) method, initial temperature of 45 °C, ultrasonic power of 535 W, and time of 41 min were considered as the optimum ultrasonic conditions for preparation of IDF with good in vitro hypolipidemic ability. Ultrasonic-treated IDF exhibited better functional and physicochemical properties than untreated IDF with significant difference (p < .05). Structural analysis from scanning electron microscope and Fourier transformed infrared spectroscopy indicated that ultrasonic treatment destroyed the microstructures of IDF from garlic straw, resulted in the honey-comb network structure and increased hydrophilic groups, which illustrated the good functional and physicochemical properties. Practical applications With the trend toward increased consumption of garlic bulb, millions of tons of straw are generally discarded every year. The productive use of such by-products as garlic straw could offer substantial economic benefits. In this work, ultrasonic technology was chosen for the modification of insoluble dietary fiber (IDF) from garlic straw. Uniform design technique helped us to get the optimum ultrasonic conditions for preparation of IDF with good in vitro hypolipidemic ability. The functional and physicochemical properties of garlic IDF were significantly influenced by ultrasonic pretreatment. The positive effect of ultrasound and application of the statistical model may be useful for functional modification and utilization of dietary fiber from garlic straw.

) originated in North America and has since spread to Asia and Europe. PWN is currently a quarantine object in 52 countries. In recent years, pine wilt disease has caused considerable economic losses to the pine forest production industry in China, as it is difficult to control. Thus, one of the key strategies for controlling pine wilt disease is to identify epidemic points as early as possible. The use of hyperspectral cameras mounted on drones is expected to enable PWD monitoring over large areas of forest, and hyperspectral images can reflect different stages of PWD. The trend of applying hyperspectral techniques to the monitoring of pine wilt disease is analyzed, and the corresponding strategies to address the existing technical problems are proposed, such as data collection of early warning stages, needs of using unmanned aerial vehicles (UAVs), and establishment of models after preprocessing.

Green citrus detection in citrus orchards provides reliable support for production management chains, such as fruit thinning, sunburn prevention and yield estimation. In this paper, we proposed a lightweight object detection YOLOv5-CS (Citrus Sort) model to realize object detection and the accurate counting of green citrus in the natural environment. First, we employ image rotation codes to improve the generalization ability of the model. Second, in the backbone, a convolutional layer is replaced by a convolutional block attention module, and a detection layer is embedded to improve the detection accuracy of the little citrus. Third, both the loss function CIoU (Complete Intersection over Union) and cosine annealing algorithm are used to get the better training effect of the model. Finally, our model is migrated and deployed to the AI (Artificial Intelligence) edge system. Furthermore, we apply the scene segmentation method using the "virtual region" to achieve accurate counting of the green citrus, thereby forming an embedded system of green citrus counting by edge computing. The results show that the mAP@.5 of the YOLOv5-CS model for green citrus was 98.23%, and the recall is 97.66%. The inference speed of YOLOv5-CS detecting a picture on the server is 0.017 s, and the inference speed on Nvidia Jetson Xavier NX is 0.037 s. The detection and counting frame rate of the AI edge system-side counting system is 28 FPS, which meets the counting requirements of green citrus.