Research indexJournal article
ТЕОРЕТИЧЕСКИЙ РАСЧЕТ МОДУЛЬНОГО ТОРСИОННОГО УПРУГОГО ЭЛЕМЕНТА
Данилов, Ivanov
VESTNIK RIAZANSKOGO GOSUDARSTVENNOGO AGROTEHNOLOGICHESKOGO UNIVERSITETA IM P A KOSTYCHEVA30 Jun 2026Open access
NobleIDark:/48914/w1/20261105/EACD610DDOI10.36508/rsatu.2026.76.79.025
ТЕОРЕТИЧЕСКИЙ РАСЧЕТ МОДУЛЬНОГО ТОРСИОННОГО УПРУГОГО ЭЛЕМЕНТА
Данилов, Ivanov · VESTNIK RIAZANSKOGO GOSUDARSTVENNOGO AGROTEHNOLOGICHESKOGO UNIVERSITETA IM P A KOSTYCHEVA · 2026
NobleIDark:/48914/w1/20261105/EACD610DDOI10.36508/rsatu.2026.76.79.025
Free to read at the publisher
You can read the abstract here, or the full text at the publisher.
Abstract
Проблема и цель. Целью настоящей работы является проведение теоретического расчета модульной подвески и его моделирование для обоснования эффективности работы модульной подвески. Методология. Методология исследования основана на теоретическом расчете угловой и линейной жесткости наборного торсиона прямоугольного сечения с использованием нормативных коэффициентов и параметров материала. На базе полученной жесткости построена математическая модель четверти прицепа, представленная системой дифференциальных уравнений второго порядка. Динамический отклик подвески на модельную неровность дороги вычислялся численными методами, что позволило оценить перемещения, углы закручивания и напряжения в элементах торсиона для различных конструктивных вариантов. Для моделирования работы подвески при динамическом переезде неровности применялся груз массой 350 кг. Искусственная неровность принималась высотой 0,05 м и длиной 0,5 м. Скорость переезда равна 5 м/с. Результаты. В результате исследования получена модель четверти прицепа, оценены жесткость рассчитанной модульной торсионной подвески. Жесткость модульной торсионной подвески равна 42939,47 Н/м. Максимальное напряжение в элементах торсиона достигает 125,9 МПа, что на 20 % ниже максимально допустимого значения. Моделирование также выявило, что время затухания колебаний кузова составляет 0,5 с, а максимальный ход кузова 18 мм. Заключение. Результаты исследования позволили оценить параметры модульной торсионной подвески, оценить эффективность ее применения. Получить достаточно данных для изготовления опытного образца, проведения стендовых и ходовых испытаний. Problem and Purpose The purpose of this study is to perform a theoretical calculation of a modular suspension system and to model its behavior in order to substantiate the efficiency of the modular torsion suspension. Methodology The research methodology is based on theoretical calculation of the angular and linear stiffness of a laminated torsion bar with a rectangular cross-section using standard coefficients and material parameters. Based on the obtained stiffness, a quarter-trailer mathematical model was developed in the form of a system of second-order differential equations. The dynamic response of the suspension to a model road irregularity was computed numerically, which made it possible to evaluate displacements, torsional angles, and stresses in the torsion elements for various design configurations. To simulate the suspension response during dynamic traversal of the obstacle, a load of 350 kg was applied. The artificial road irregularity was modeled as being 0.05 m high and 0.5 m long, with traversal speed set to 5 m/s. Results The study resulted in a validated quarter-trailer model and an estimation of the stiffness of the designed modular torsion suspension system. The stiffness of the modular torsion suspension was determined to be 42,939.47 N/m. The maximum stress in torsion elements reached 125.9 MPa, which is 20% below the allowable limit. Modeling also showed that body oscillations decay within 0.5 s, and the maximum body travel is 18 mm. Conclusion The obtained results make it possible to evaluate the performance of the modular torsion suspension, confirm the feasibility of its application, and provide sufficient data for fabrication of a prototype followed by bench and field testing.